Aichi Tokei Denki Vietnam, OF10ZAT-AR Microstream Flow Sensor

Standard specifications

Model		OF05ZAT	OF10ZAT	OF05ZZT	OF10ZZT
Flow rate range	Liquid viscosity0.3 – 0.8mPa・s	0.085 – 0.85L/min	0.7 – 5L/min	0.085 – 0.85L/min	0.7 – 5L/min
	Liquid viscosity0.8 – 2.0mPa・s	0.05 – 0.85L/min	0.35 – 5L/min	0.05 – 0.85L/min	0.35 – 5L/min
	Liquid viscosity2.0 – 5.0mPa・s	0.017 – 0.85L/min	0.17 – 5L/min	0.017 – 0.85L/min	0.17 – 5L/min
	Liquid viscosity5.0 – 200mPa・s	0.0085-0.85L/min	0.085 – 5L/min	0.0085 – 0.85L/min	0.085 – 5L/min
Accuracy		±2%RS(In the standard installation position)
Measurable liquid	Types of measurable liquid	Please decide based on the major materials exposed to the fluid, which are described below.
	Major measurable liquid	Cold and hot water and heating, light and heavy oil		Mildly acidic and mildly alkaline liquid
Maximum operating pressure		0.5MPa(When the liquid is at 20°C).
Pressure loss		4 kPa or less	10 kPa or less	4 kPa or less	10 kPa or less
Fluid temperature range		-10 to +70℃(No condensing)
Responsiveness		-10 to +70℃ 35～85%RH(No condensing)
Output signal	Voltage pulse output	Voltage pulse 3-wireLength of wire: Approx. 480 mmVoltage pulse duty ratio 2/8 < A/B < 8/2When voltage is applied at 12 VDC or less,High: 10 VDC or moreLow: 1 VDC or less
	Open collector output	Open collector pulse (Capacity: 6 mA DC or less)Length of 4 lead wire: Approx. 600 mm
Pulse constant		0.46mL/P	2.5mL/P	0.46mL/P	2.5mL/P
Maximum frequency		Approx. 31Hz	Approx. 34Hz	Approx. 31Hz	Approx. 34Hz
Minimum pulse width		Approx. 0.0065s	Approx. 0.006s	Approx. 0.0065s	Approx. 0.006s
Applied voltage range		3 – 24VDC *1
Power consumption		0.2VA or less
Structure		Splash-proof structure (IP64 compatible) for indoor use
Connection		R1 / 4	R1 / 2	R1 / 4	R1 / 2
Mass		Approx. 100 g	Approx. 140 g	Approx. 100 g	Approx. 140 g
Major materials of the part exposed to liquid	Case	PPS
	Rotor	PPS
	O-ring	NBR		FKM
	Shaft	SUS304		SiC

– If the fluid might contain fine particles, please install the filter with a #80 mesh screen or higher before the flow sensor. – Do not measure gasoline, sodium hydroxide (caustic soda), oxygenated water (Oxydol) and acidum hydrochloricum (strong acid fluid). *1. Apply the same voltage to the sensor power supply (red – black) and pulse output (blue and white – black). (Applicable only for open collector output)